Aim Sports Wraith 15" AR15 Handguard - M-LOK

12

| Write a Review

Ratings Snapshot

4.8

out of 5

5 (10)

4 (2)

3 (0)

2 (0)

1 (0)

Would recommend this product.

100%

SKU: 136-AIMS-US-AS003

I bought this 15 inch m lok handguard for a Windham flat top AR15. With a suppressor and the original gas block, the rifle was very overpressured, so I wanted to put on an adjustable gas block. I bought this handguard to go over the gas block. I do not have a lot of experience with customizing ARs, but this handguard was very easy to install. It fit perfectly and looks great. I would absolutely recommend this to anyone looking for a good deal.

The 15 inch ar rail is awesome for the low price had a small blemish at an attatchment point can't even notice once I put a rail piece on the only real down side is I had to take a small metal file and do a couple of swipes on the anti rotation tabs they would not fit past the upper

I was in search of a quality 15 inch m lok handguard that wouldn't break the bank. I wasn't familiar with this manufacturer and couldn't find much in the way of reviews, but decided to take a chance anyway. I have not been disappointed. The finish is on par with other manufacturers' components used on the remainder of the build. The fit is precise and secure. I'm impressed with the looks, slim design and the light weight. I will be ordering another.

This 15 inch AR 15 handguard is super light and great for the price! I was building a plinker and needed a sturdy rail that wasn’t bulky and would last, this did the trick! The coating does scratch easily but if you don’t care about appearance this rail it great!

SUPER LIGHT 15 inch m lok handguard! Feels great and did exactly what I needed it too (get rid of the A-post gas block). Easier to install than a lot of the higher-end hand guards. The mounting design means you don't have to worry about lining up the gas tube with any specific hole or gap in the barrel nut. It secures nicely and there's zero movements. Top rails lines up perfectly with my PSA upper.

I ordered this 15" ar15 handguard to see how well it worked for my project. I found it to be made very well and surprisingly lightweight. Fit and finish of it is very nice and it provides close tolerances between the upper and the barrel nut. I compared the outer width and overall feel to a Seekins NOxs rail and was surprised at how similar they were to each other. The anodizing looked evenly applied and was blemish free, although I cerakoted it for my project. Installation was very easy, first install and torque the barrel nut, then install the two bolts and capture bits through the rail and then the barrel nut. I've been very happy with this product and have purchased two more for additional projects.

For the money this AR rail is nice and easily installed, I’ve ran several other rails 3x the price and this rail seems solid as most others and comes with steel barrel nut and hardware! Only bad thing is inside diameter of rail is too small for most suppressors if u wanted that look!

I got the 15" AR-15 handguard. It was very easy to install with the provided barrel nut. The two anti rotation "stumps" or whatever you call them on top give me confidence that these are going nowhere. Magpul M-Lock rails were easy to install. And most importantly it looks great! Mounted on a DPMS Oracle (Had to get the low profile gas block). Fired today with no problems and was a major upgrade for a low price

I decided to save a little money and give these 15 inch m lok handguard from Aim a chance. Figured for the price, if they were crappy, I would abuse them for a bit and replace them, no harm no foul. I can say that they absolutely blew my expectations out of the water. They are extremely well built, no sharp corners, true MLOK, and the anti-rotation tabs are a bonus. The Steel Barrel nut tightens down firm, and locks the handguard in place securely with the two screws provided. I added a dab of blue loctite on the two handguard tension screws for good measure. Overall, I couldn't be happier with these and plan to use them exclusively for all my builds.

The best ar 15 handguard combination of weight, cost, made in USA, and aesthetics is! Lots of mlok slots make for easy/fast barrel cooling and mounting options offset between the 12,3,6,9 o'clock positions. I have both the AR-15 and AR-10 versions. Word to the wise, when they say apply minimal torque to the clamp screws/bolts, they mean it; they strip extremely easy. I could subtract a star for that, but they do warn the installer not to over-tighten, it's my fault for not following the instructions.

This ar handguard is nice aesthetically. Fits perfectly on my 22 lr dedicated conversion of my 5.56 ar rifle. The tabs for the anti-rotation system were a perfect fit. Even the Picatinny rails match up pretty good. An only minor complaint is the barrel nut does not fit my ar tool. Had to use an adjustable wrench under a cloth to prevent marring the nut. Thus I cannot use my torque wrench. Just guesstimated the force on the nut. It is just a 22lr so hopefully, the recoil and bolt impact will be small to get it loose. Still a very nice fit. Love the look. Just what is to be expected from a "Made in the USA" product. I would buy again to replace the delta handguard on my 300 black ar rifle.

It's a pretty basic AR Handguard, but perfectly adequate and in an ideal length for many projects. The nuts can strip easily, so be gentle installing. I have used this on AR builds and the Tippmann M4-22 successfully. Feels sturdy, and does not feel cheap at all.