Weaver #402 Top Mount Bases

1

| Write a Review

Ratings Snapshot

5.0

out of 5

5 (1)

4 (0)

3 (0)

2 (0)

1 (0)

Would recommend this product.

100%

SKU: 105-WVR-48420
Manufacturer: Weaver
MFG#: Weaver 48420

Weaver #402 Bases

Each Weaver mount base is machined to tight tolerances for a custom fit. These Aluminum bases offer maximum strength for rings to hold tight

Rear extension Weaver 402 base for:

• Navy Arms Country Boy Muzzleloader
• Savage Axis Series, 10, 12 & 16 (Short Actions ). Striker , Pistol , 510, 512, 516 S/A, 10 ML (2-piece only) Pre 2003 Models,10,12,110, 112 (All Long Action Accutrigger), 10,12,110, 112 (All Short Action Accutrigger), 10 ML II
• Stevens Savage/Stevens 200

Front extension Weaver 402 base for:

• Anschutz 1568
• Browning Bolt Action BBR, Hi-Power, other calibers (older models), BBR (Bolt Action), Long & Short Actions
• Churchill 950 & 950-C, 972-C
• Marlin 455, MR7
• Mauser Receiver Ring about 1.410" diameter (98FN), Receiver Ring about 1.300" Diameter (Swedish 96), Bauer 3000 & 4000
• Musgrave Mark I, Mark II, Mark III, Mark IV
• Navy Arms Country Boy Muzzleloader
• Parker-Hale 1000, 1000C, 1100, 1200 & 1700
• Colt 57
• Cooey 71
• Enfield Winchester 70
• H&R 300, 301, 330, 370 (Pre 1973), 300 & 301 L.A. in 270, 30-06, 7mm & 300 Win (1973+)
• Herters J9
• High-Standard High-Power
• Interarms Viscount
• Savage Axis Series, 10, 12 & 16 (Short Actions). Striker, Pistol, 510, 512, 516 S/A, 10 ML (2-piece ONLY) Pre 2003 Models. 110, 112, 116 (Long Actions); 210 Shtg (use X-high rings )Pre 2003 Models. 10, 12, 110, 112 (All Long Action Accutrigger), 10,12,110, 112 (All Short Action Accutrigger), 10 ML II
• Schultz & Larsen Schultz & Larsen
• Sears 50, 51, 51L, 53
• Smith & Wesson Mauser Actions with small rectangular ring about 1.30" diameter
• Stevens 110E, Savage/Stevens 200
• Voere 2150, 2165/1, 2165/2, 2165/3 & 2165/4 (Mauser Action)
• Weatherby FN Mauser style actions
• Winchester 52 with the hole spacing same. Lever Actions 53, 55, 64, 65, 66, 71, 1886, 1892, 95 & 1895, 54, & early Models. 70 with Serial No. below #66 350, 70 Long Action with the hole spacing same, 670, 770, 70 Long Action with hole spacing different & 70 Super Express, 70 Short Action (1984+), 70 Long Action with hole spacing different & 70 Super Express, 70 Short Action (1984+), 70 WSM

Note: For the Mauser Receiver Ring about 1.410" diameter (98FN), Receiver Ring about 1.300" Diameter (Swedish 96), Bauer 3000 & 4000 shimming is probably required for perfect scope alignment. The rear base may require modifications for correct fit to military actions

Note: Savage 110, 112, 116 (Long Actions); 210 Shtg (use X-high rings) Pre 2003 Models, 10, 12 & 16 (Short Actions). Striker, Pistol, 510, 512, 516 S/A, 10 ML (2-piece ONLY) Pre 2003 Models, 10, 12, 110, 112 (All Long Action Accutrigger), 10,12,110, 112 (All Short Action Accutrigger), 10 ML II, Stevens Savage/Stevens 200 or shorter tube scopes or red dot scopes use #402 extension front base or one-piece base if available. Extension base allows an extra .689"

Note: The Winchester 52 with the hole spacing same may require bolt and/or safety alteration, otherwise firearm cannot function safely and properly. Consult with a qualified gunsmith. For the Winchester 52 & Winchester 70 Long Action Rifles - check the spacing of the tapped holes for the rear base and compare it to the hole spacing for the front base. For the same hole spacing, Model 70, use 47+ 46

Note: The Winchester Lever Actions 53, 55, 64, 65, 66, 71, 1886, 1892, 95 & 1895 will have to be drilled and tapped

Note: The Winchester 54, & early Models, 70 w/Serial No. below #66 350 may require bolt and/or safety alteration or the firearm will not function safely and properly. Consult with a qualified gunsmith

Note: For the Winchester 70 Long Action with the hole spacing same, 670, 770, 70 Long Action, 70 Long Action with the hole spacing different & 70 Super Express with the hole spacing different & 70 Super Express The handiest way to pinpoint the correct base for the Winchester 52 & 70 Long Action Rifles is to check the spacing of the tapped holes for the rear base and compare it to the hole spacing for the front base. If the hole spacing is the same, then use 46+ 46 for Model 52 and use 47+ 46 for Model 70. If the hole spacing is different, use 25+ 57 for Model 52 and 49A+ 46 for Model 70

This scope mount will work with Weaver style scope rings.

Color Mount:
105-WVR-48108 Gloss Black
105-WVR-48430 Silver

The distinction between inferior quality and premium Scope Mount Base is undeniable. At MSP, we only offer Scope Mounts from the most trusted brands like Weaver. Buy with confidence that we stand behind the product we sell.