Ghost Rocket 3.5 lb.Trigger Connector for Glock Gen 1-5

10

| Write a Review

Ratings Snapshot

5.0

out of 5

5 (10)

4 (0)

3 (0)

2 (0)

1 (0)

Would recommend this product.

100%

SKU: 113-GHO-2105-A-1
UPC: 644406121053
Manufacturer: Ghost Inc.
MFG#: GHO_2105-A-4

Put this ghost rocket connector in my Glock 26 along with a smooth-faced trigger. It is precisely what I was looking for; the pull is very light and smooth.No stacking like the factory trigger and no over travel. You should be able to be comfortable taking your gun completely apart before you do this, though. The instruction on the Ghost website is also a must to follow. Also, get the Glock orange slide plate that is sold here too.

This ghost rocket connector works well. It is easy to install, provided you have the correct tools. However, it isn't straightforward to adjust the trigger stop. That adjustment will require that you dis-assemble and re-assemble your Glock many times to get the halt just right. Once installed, it is a bit of magic, and it dramatically improves the Glock trigger pull.

Pretty good product. I have a glock 19. Had to grind .060 inch off of tab; in order to fire. As per the instructions.

Pretty good product. I have a glock 19. Had to grind .060 inch off of tab; in order to fire. As per the instructions.

You have to fit the trigger stop by gradually shortening it, so this isn't a drop-in, but believe me, it's worth it! It took me about an hour and a half working slow, getting all goofed up and having to disassemble the slide to get the striker out so I could get the gun apart on my first few trial fittings. Remember, it's a trigger stop, and while it's long, you can't pull the trigger! When you get close to the right length, you can trip the trigger bar with the disassembly tool or a pin punch through the armorer's orange slide cover plate (get one of these!), and that makes try fitting much easier. Google Ghost inc. And see their instructions before you start. I fitted mine with the "Dave Spalding cut" (google that too), and the reset is astonishingly short. Dave, I owe you, one buddy! Long story short, this thing works amazingly well; the Spalding cut is the away to go, and if I can do it, anyone can. I used a file to do most of the cutting and a stone for the last bit and to polish. Work slow, check the fit often, and don't forget to buy an armorer's orange slide cover plate!

Install a ghost rocket connector on Glock 17 Gen4. Install was easy - get the half backplate from ghost inc. This is a short piece needed for an easy install. Trigger now feels about a pound lighter, with no overtravel, and the reset is way fast (almost too fast)! Very tedious to install, but worth it in the end.

Have shot a Glock 21 after replacing factory 5.5 trigger with a 3.5 ghost trigger. This one helped speed up my recovery between shots and assuring better time on target recovery. Follow the easy instructions that are written and accompanied with pictures. If you've been shooting for awhile with the factory trigger be patient with the new one. You have to train new muscle memory to not press as hard at reset or you will crank off an unsited round. I don't recommend for conceal carry use for that reason.

I like these, the best solution for trigger overtravel adjustment. It takes a while to get it right the first time, but then I use a properly adjusted one as a template for future ones. DEFINITELY get the orange slide cover and thank me later.

I purchased 4 of these ghost rocket connector for install on four different Glocks. 3 Gen 3's and a Gen 4. It takes about 15 to 30 minutes to get it fit properly to each gun if you take your time. And can altogether remove overtravel in the trigger after the break. I installed this with three different Apex Triggers. The best combination was with Trigger part number 100023505. It was a blue one with narrow safety. The take up was nice and light with the pressure coming up just before the break. After the first round, the reset is nice and short with a gentle smooth pull to re-fire. All of the Apex triggers had an extremely soft pull with this connector. The Stock Trigger was certainly improved and lighter than stock but needed to be smoothed out to improve the feel. I recommend the Apex Trigger with the new trigger bar for the best overall improvement to the feeling. If you get one of these, you will need the Armorers Slide Cover Plate, 100001260, to release the trigger when doing the setup. you technically "Could" do it without it, but the cover plate is cheap enough. Just add it to the cart and save yourself the frustration!

This Glock trigger connector was a little irritating to fit, but once it was fit, WOW it is amazing. I have the ghost 4.5-pound striker spring, 6pound trigger spring, and a reduced safety plunger spring. The combination is fantastic. It improved tremendously with over travel. Note: You do need a armorers back plate for the install/fitting of the connector.