EGW Sight Mount For the Burris Fastfire, Vortex Venom & Viper for CZ P10C / P10F Sight Mount

2

| Write a Review

Ratings Snapshot

5.0

out of 5

5 (2)

4 (0)

3 (0)

2 (0)

1 (0)

Would recommend this product.

100%

SKU: 198-49329
UPC: 841370116010
MFG#: EGW 49329

EGW Sight Mount For the Burris Fastfire, Vortex Venom & Viper for CZ P10C / P10F Sight Mount

Mounting Hardware is Included

This Mount Fits:

• CZ P10C
• CZ P10F
  

This Mount Does Not Fit:

• CZ P10C Optics Ready
• CZ P10F Optics Ready

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs

Mounting Hardware:
(2) 6-32 Button Head Screws
(2) 6-32 Flat Head Screws
(1) 6-32 Set Screw

Red Dot Fitment:

• Vortex Viper
• Vortex Venom
• Burris FastFire
  • Burris FastFire 2
    • Burris FastFire II
  • Burris FastFire 3
    • Burris FastFire III
  • Burris FastFire 4
    • Burris FastFire IV
• Docter
• ADE RD3-001
• ADE RD3-002
• ADE RD3-009
• UTG Reflex Micro Dot
• Crimson Trace CTS-1200
• Crimson Trace CTS-1300
• Sightmark Mini Shot
• Sightmark Core Shot

The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.

*All ADE mounts require 6-32 x 3/8" screws.

Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.

Details:

EGW's red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.

Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

The screws that are included with this mount require a 5/64'' allen wrench for installation.

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

Alt Description:

• CZ P10C Vortex Venom mount
• CZ P10F Vortex Venom mount
• CZ P10C dovetail red dot mount
• CZ P10F dovetail red dot mount

Vortex Venom Quick Links:

• Vortex Venom
• Vortex Venom for sale
• Vortex Venom glock mount
• Vortex Venom on ar15
• Vortex Venom picatinny mount
• Vortex red dot
• Venom red dot
• Vortex Venom on shotgun
• Vortex Venom red dot for sale
• Vortex Venom red dot
• Vortex Venom ar mount
• Vortex Venom offset mount

The distinction between inferior quality and premium scope mount is undeniable. At MSP, we only offer red dot mounts from the most trusted brands like Evolution Gun Works. Buy with confidence that we stand behind the product we sell.