Savage 110 Long Action Round Back Picatinny Rail

Description

EGW Steel HD Savage Long Action Round Back Picatinny Rail

Mounting Hardware is Included

This mount fits:

Savage Model 110 Long Action Round Rear Receiver
Savage Model 111 Long Action Round Rear Receiver
Savage Model 112 Long Action Round Rear Receiver
Savage Model 114 Long Action Round Rear Receiver
Savage Model 116 Long Action Round Rear Receiver
Stevens Model 200 Long Action Round Rear Receiver

This mount does not fit:

Savage Edge
Savage Axis
Savage Axis II
Savage Model 25
Savage Long Actions with Flat Rear Receivers
Savage Medium Actions with Flat Rear Receivers
Savage Long Actions Drilled for #8 Screws

Please check your mounting screw diameter and hole spacing before placing your order to ensure you select the correct mount. Screw diameter and hole spacing information can be found in the description tab below.

Machined From: Solid 4140 Steel
Finish: Parkerized
Center Spread: 4.630"
Overall Length of Mount: 7.458"
Height: .35" (Top of Receiver to Top of Picatinny)
Weight: 5.6 oz
Quick Disconnect Ring Compatible: Yes
Ambidextrous: Yes
Compatible with Picatinny or Weaver scope rings.
Mounting Hardware: #6-48 X 1/4 Screws and T-10 Bit Included
Torque Specs: 20 in/lbs
Compatible with Picatinny Scope Rings or Weaver scope rings.

Evolution Gun Works Savage bases will work with any long action round back Savage rifle with an ejection port. It is alsocompatible with the Stevens Long actions.

The round back on this mount will accommodate rounded receivers, and guns that have an accu-trigger.

Savages without an accu-trigger will require our flat back mount (listed separately).

This mount comes standard with a bevel on both sides making it ambidextrous.

We recommend measuring the hole spacing in your receiver to confirm it matches with the dimensions we have published.

Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories. Our one-piece scope mounts are the obvious choice for hunters and tactical shooters alike.

These bases sit at approximately 0.35" high.

Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories. The cross slots are also machined the full width of the mount and gauged to MIL-STD 1913 specs maintaining tolerances of +/-.002".

After machining; the mounts are sand blasted. The steel rails are Mil Spec parkerized for a durable rust resistant finish.

Werecommend:
0 MOA -if shooting 0-500 yards
20 MOA -if shooting 500-1000 yards

When zeroing your rifle with a 20 MOA mount, we recommend zeroing at 200 yards.

Compatible with Picatinny or Weaver scope rings. Add EGW HD Scope Rings to make it a complete package!

From manufacturing to packaging, EGW products are made with pride in the USA.

Installation: EGW recommends 20 inch lbs of torque and a drip of blue loctite (loctite is available through our website and is sold separately).

When zeroing your rifle with a 20 MOA mount, we recommend zeroing at 200 yards.

The entire mount and accessories (from the mounting screws and wrench down to the packaging) are made in the USA.

This mount is made specifically for the Browning X-Bolt Short Action. Please check your center spread and select the correct mount. There have been issues with some guns being chambered for a certain action length and having a different length action. EX: 22-250 in a WSSM action. Please make sure the scope mount you are selecting has the correct center spread!

These bases sit at approximately 0.525” high.

Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories. The cross slots are also machined the full width of the mount and gauged to MIL-STD 1913 specs maintaining tolerances of +/-.002".

After machining; the mounts are tumbled and sand blasted. The aluminum mounts are Type III hard coat anodized for long lasting durability. The steel rails are Mil Spec parkerized for a durable rust resistant finish.

We recommend:
0 MOA - if shooting 0-500 yards
20 MOA - if shooting 500-1000 yards

When zeroing your rifle with a 20 MOA mount, we recommend zeroing at 200 yards.

Compatible with Picatinny or Weaver scope rings. Add EGW’s HD Scope Rings to make it a complete package!

From manufacturing to packaging, EGW’s products are made with pride in the USA.

Installation: EGW recommends 20 inch lbs of torque and a drip of blue loctite (loctite is available through our website and is sold separately).

Alt Description:

Savage 110 picatinny rail
Savage Model 111 Picatinny rail
Savage Model 112 Picatinny rail
Savage Model 114 Picatinny rail
Savage Model 116 Picatinny rail
Stevens Model 200 Picatinny rail
Savage Model 111 Scope Base
Savage Model 112 Scope Base
Savage Model 114 Scope Base
Savage Model 116 Scope Base
Stevens Model 200 Scope Base
Savage Model 111 Scope Mount
Savage Model 112 Scope Mount
Savage Model 114 Scope Mount
Savage Model 116 Scope Mount
Stevens Model 200 Scope Mount

Savage 110 Quick Links

Choose from a wide variety of Scope Rings

The distinction between inferior quality and premium Savage 110 scope base is undeniable. At MSP, we only offer Savage 110 Accessories from the most trusted brands like EGW Mounts. Buy with confidence that we stand behind the product we sell.

WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to - www.P65Warnings.ca.gov.

Customer Ratings & Reviews

Ratings Snapshot

5.0

out of 5

5 (1)

4 (0)

3 (0)

2 (0)

1 (0)

5.0

out of 5

5 (1)

4 (0)

3 (0)

2 (0)

1 (0)

1 Total Reviews

Picatinny rail for Browning X Bolt short action

5 out of 5

Hunter E

Location:

Date: November 5, 2019

Perfect for long-range guns to get the most of your scope. 0 moa would be great for regular hunting rifles as the mount is super sturdy with little worries about “knocking” the scope off.

Recommended

1 Total Reviews