EGW Sight Mount For the Burris Fastfire, Vortex Venom & Viper Desert Eagle Pre 2017 Sight Mount

1

| Write a Review

Ratings Snapshot

5.0

out of 5

5 (1)

4 (0)

3 (0)

2 (0)

1 (0)

Would recommend this product.

100%

SKU: 198-49303
UPC: 841370115716
MFG#: EGW 49303

EGW Red Dot Mount for the Docter, Burris Fastfire, Vortex Venom, and Vortex Viper Desert Eagle Pre 2017 Sight Mount

Mounting Hardware is Included

This mount fits:

• Desert Eagle Pre 2017

This mount fits:

• Desert Eagle Post 2017
• Baby Desert Eagle Post 2006

Please take note to the Pre 2017 and Post 2017 differences when placing your order.

• Pre 2017 rear shelf behind the dovetail is .187"
• Post 2017 rear shelf behind the dovetail is .120"

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs

Red Dot Fitment:

• Vortex Viper
• Vortex Venom
• Burris FastFire
  • Burris FastFire 2
    • Burris FastFire II
  • Burris FastFire 3
    • Burris FastFire III
  • Burris FastFire 4
    • Burris FastFire IV
• Docter
• ADE RD3-001
• ADE RD3-002
• ADE RD3-009
• UTG Reflex Micro Dot
• Crimson Trace CTS-1200
• Crimson Trace CTS-1300
• Sightmark Mini Shot
• Sightmark Core Shot

The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.

*All ADE mounts require 6-32 x 3/8" screws.

Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.

Evolution Gun Works red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.

Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included.

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

The screws that are included with this mount require a 5/64'' allen wrench for installation.

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

Alt Description:

• Vortex venom on desert eagle
• Desert eagle red dot mount

Vortex Venom Quick Links:

• Vortex Venom
• Vortex Venom for sale
• Vortex Venom glock mount
• Vortex Venom on ar15
• Vortex Venom picatinny mount
• Vortex red dot
• Venom red dot
• Vortex Venom on shotgun
• Vortex Venom red dot for sale
• Vortex Venom red dot
• Vortex Venom ar mount
• Vortex Venom offset mount

The distinction between inferior quality and premium Vortex Viper Mount undeniable. At MSP, we only offer Red Dot Mounts from the most trusted brands like Vortex Optics. Buy with confidence that we stand behind the product we sell.