My Cart: 0 item(s)

Every Shot Counts - Shipping Starts at 5.95
Product Search

Secure Checkout
EGW Red Dot Sight Mount for S&W 1911 Adjustable Sight fits Burris Fastfire, Vortex Venom & Viper
    EGW Red Dot Sight Mount for S&W 1911 Adjustable Sight fits Burris Fastfire, Vortex Venom & Viper
    Purchase EGW Red Dot Sight Mount for S&W 1911 Adjustable Sight fits Burris Fastfire, Vortex Venom & Viper
    • EGW Red Dot Sight Mount for S&W 1911 Adjustable Sight fits Burris Fastfire, Vortex Venom & Viper
      Not Yet Rated | Write the First Review SKU: 198-49296
      UPC: 841370116959

    • MSRP: $49.99
      $47.49

      Quantity in Basket:  None

    •  

    EGW Red Dot Mount for the Docter, Burris Fastfire, Vortex Venom, and Vortex Viper for S&W 1911 Adjustable Sight Mount

    Mounting Hardware is Included

    This mount fits:

    • Smith & Wesson 1911s with adjustable rear sights

    Material: 7075 Aluminum
    Coating: Matte Black Hardcoat
    Overall Length: 1.811"
    Overall Width: .99"
    Torque Specs: 15 in/lbs

    Mounting Hardware:
    (2) 6-32 Button Head Screws
    (2) 6-32 Flat Head Screws
    (1) 6-32 Set Screw

    Red Dot Fitment:

    The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.

    *All ADE mounts require 6-32 x 3/8" screws.

    Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.

    EGW red dot mounts red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.

    Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.

    Installation Instructions
    - Remove the rear sight*
    - Install the EGW Sight Mount in the dovetail
    - Tighten set screw (if applicable)
    - Place the red dot sight on the EGW Sight Mount
    (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
    - Apply blue Loctite to the provided mounting screws
    - Torque mounting screws to 15in/lbs

    2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
    2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

    The screws that are included with this mount require a 5/64'' allen wrench for installation.

    Modification of your firearm may nullify the manufacturer's warranty.
    This product should be installed and checked by a qualified gunsmith.
    No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

    Vortex Venom Quick Links:

     


    The distinction between inferior quality and premium scope mount is undeniable. At MSP, we only offer 1911 Accessories from the most trusted brands like Evolution Gun Works. Buy with confidence that we stand behind the product we sell.

    WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to - www.P65Warnings.ca.gov.

    Customer Ratings & Reviews

    Be the first to rate this item!

    Write Review


    Related Products