EGW Red Dot Mount for the Docter, Burris Fastfire, Vortex Venom, and Vortex Viper for Ruger SR9, SR4

1

| Write a Review

Ratings Snapshot

5.0

out of 5

5 (1)

4 (0)

3 (0)

2 (0)

1 (0)

Would recommend this product.

100%

SKU: 198-49290
UPC: 8.4137E+11

EGW Red Dot Mount for the Docter, Burris Fastfire, Vortex Venom, and Vortex Viper for Ruger SR9, SR40, SR45

This mount fits:

• Ruger SR9
• Ruger SR9C
• Ruger SR40
• Ruger SR40C
• Ruger SR45

This mount does not fit:

• Ruger SR9E
• Ruger SR22

Any Walther model that comes with the standard sights that have the detent will work with this mount. This mount now comes with a set screw allowing it to be used with the friction fit dovetails as well.

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs

Mounting Hardware:
(2) 6-32 Button Head Screws
(2) 6-32 Flat Head Screws
(1) 6-32 Set Screw

Red Dot Fitment:

• Vortex Viper
• Vortex Venom
• Burris FastFire
  • Burris FastFire 2
    • Burris FastFire II
  • Burris FastFire 3
    • Burris FastFire III
  • Burris FastFire 4
    • Burris FastFire IV
• Docter
• ADE RD3-001
• ADE RD3-002
• ADE RD3-009
• UTG Reflex Micro Dot
• Crimson Trace CTS-1200
• Crimson Trace CTS-1300
• Sightmark Mini Shot
• Sightmark Core Shot

The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.

*All ADE mounts require 6-32 x 3/8" screws.

Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.

EGW red dot mounts red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.

Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

The screws that are included with this mount require a 5/64'' allen wrench for installation.

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

Alt Deescription:

• Ruger SR9 Red Dot Mount
• Ruger SR9C Red Dot Mount
• Ruger SR40 Red Dot Mount
• Ruger SR40C Red Dot Mount
• Ruger SR45 Red Dot Mount
• Ruger SR9 Vortex Venom Mount
• Ruger SR9C Vortex Venom Mount
• Ruger SR40 Vortex Venom Mount
• Ruger SR40C Vortex Venom Mount
• Ruger SR45 Vortex Venom Mount

The distinction between inferior quality and premium scope mount is undeniable. At MSP, we only offer Ruger SR9 accessories from the most trusted brands like Evolution Gun Works. Buy with confidence that we stand behind the product we sell.