Ghost Grip Plug for Glock Gen 1-3 - Medium & Large Frames

10

| Write a Review

Ratings Snapshot

4.9

out of 5

5 (9)

4 (1)

3 (0)

2 (0)

1 (0)

Would recommend this product.

100%

SKU: 113-GHO-GPM
UPC: 644406240013
Manufacturer: Ghost Inc.
MFG#: G-PLUG

I have often looked at that hole between the back of the pistol grip and the magazine well, thinking, "why is that there?" While in the field, dirt, dust, sand, etc., are Collecting in there. It becomes another area to clean on the gun. I finally decided to "close it up" on my .40 cal Glock 22. The Ghost Grip Plug works excellent. It easily snaps in place by following the instructions on the back of the packaging. I recommend it.

It was installed in Gen 3 Glock 19 with a great fit, good color, and texture match. Item was installed without modification. However, some slight flash from the mold lines could be seen around the edge, a roll punch was used to uninstall, and a sharp, clean razor blade was pulled along the flashing to create a smooth edge before reinstallation. Not sure about how compatible the product is with most ouija boards, after three attempts, there still has been no contact from the ghosts in the plug, a professional seance is being considered; for the money, it would have been acceptable just to have gotten a message from my recently deceased grandmother, but that did not occur either. The exaggerated radius on the leading edge facing the magazine well aids quick reloads, but after having intentionally dropped the Glock on its frame, the kitchen chairs sometimes stack themselves when no one is looking. Overall an excellent product; I would recommend it, and it is one of my favorite Glock 19 accessories.

I bought two grip plugs for my gen 3 blocks. Glock 19 and the larger frame Glock 34. They both fit fine. Although the gen 4 are a bit different in size. The Glock 19 has a shorter grip as to the 34, but the plugs are the same size . Hope that answers your question

The Ghost Glock grip plug arrived promptly. Pretty simple to install, just pop it into place with your palm. It looks like some folks are breaking these by trying to bend the retaining "nub" during the installation. Don't do that. Just palm the plug in.

Bought this Glock grip plug for a 3rd gen Model 17. The button tab is very stiff, and I was afraid to pound the plug into place, fearing it may crack or bulge the rear of the grip. But, by slightly depressing the button with a flat screwdriver while simultaneously hitting the plug lightly with a rubber mallet, it snapped right into place. Nice and tight, just like I hoped. Glad I bought it, as I think it will make speed reloads smoother, and it just makes the grip look "finished."

Well, I took a chance, on this Glock grip plug gen 3 tp see of it work on an an IWI Jericho 941PSL, and it fits just like it was made for it. TIP, You have to push in on the tab with a small screw driver and push down on the bottom (base) at the same time. More pushing down then in on the tab, once you get the tab just inside the grip push down hard, goes right in. The tab is hard to move; you could break it off, if your not careful.

This glock plug gen 3 was very easy to install. I don't see why the instructions say you should have a gunsmith install it if you did, you shouldn't own that firearm. It made the magazine fit tighter, which I like.

This plug fills in the hole that Glock leaves at the bottom of the handgrip. I don't know why they do that, but it makes the gun look "unfinished." This little Ghost Inc. Glock handle plug fits right, looks 100% better. Good product!

I have five Glocks. Two of them G19s. These not only plug up the hole but extend and reshape the backstrap area to fit the hand better.

For the price, you can't beat this product. Magazine changes are simplified and dirt and debris is prevented from entering the pistol from this point of entry for around $7 bucks.